So I self host some stuff like jellyfin, ssh server for borg backup etc. over lan(Asus RT-AX53U router).

And just noticed that i still use cat5 and cat5e cables.

Does it make sense to upgrade to newer cat8 cables?

  • nattekrant@feddit.nl
    link
    fedilink
    arrow-up
    11
    ·
    edit-2
    1 year ago

    First and foremost, the user that adviced you to look at the connection speed is 100% right. If you establish a gigabit link with a gigabit device, it makes no sense to upgrade other than future proofing.

    There’s no point in going beyond Cat 6a. Keep in mind that the length of the cable is a big factor as well. For 1/2.5GbE, Cat 5e is plenty (for at least 100m). If you plan on going to 5/10GbE now or in the near future, Cat 6a will get you there with ease (for at least 100m). In both cases, keep the cable as close to the required length as possible + a 30cm/1ft service loop (slack) on each end. That will cause no more signal degradation then necessary and make for a clean install.

    • boo@beehaw.orgOP
      link
      fedilink
      arrow-up
      1
      ·
      1 year ago

      I wonderbif there is a way to measure this. Like a speed test for LAN.

      • nattekrant@feddit.nl
        link
        fedilink
        arrow-up
        1
        ·
        1 year ago

        Iperf is the standard for measuring speeds between devices, remote OR local. Can you be more specific about what you mean by “This”?

  • qjammer@lemmy.ml
    link
    fedilink
    arrow-up
    6
    ·
    1 year ago

    What you should be asking is whether the cables qre the bottleneck in your network or not.

    Is there any link that is not negotiating 1Gbps? Do you have devices that could push 10Gbps but the cable is not allowing it? If not, then there’s no need to upgrade them.

    Unless, of course, if you want to do it just for fun, which is also a legitimate reason 😄

    • boo@beehaw.orgOP
      link
      fedilink
      arrow-up
      0
      ·
      1 year ago

      Right? I also wanted slightly longer 2m cables, but thats secondary.

      • cnnrduncan@beehaw.org
        link
        fedilink
        arrow-up
        1
        ·
        1 year ago

        A 2 metre 5e cable will be a hell of a lot cheaper than a 2m CAT8 cable, and unless your internal network is faster than a gigabit or two there’s really no point in using anything more expensivethatn 5e or maybe 6.

        • nattekrant@feddit.nl
          link
          fedilink
          arrow-up
          2
          ·
          1 year ago

          Cat 5e supports 5 and 10GbE at least for 10 meters. I wouldn’t bet on it considering the price of Cat 6a but 2 meters is really short.

  • Pepparkakan@lemmy.ml
    link
    fedilink
    arrow-up
    2
    ·
    1 year ago

    If it’s actually Cat.5 then it may be worthwhile to look at replacing with something newer, but if you’re on Cat.5e then unless you wanna start playing with 10Gbit you’ll probably be fine.

    If you do upgrade, you don’t need to go to Cat.8 simply because it exists. Cat.6a or even plain Cat.6 will do everything you’re gonna need in Gbit networks.

  • mrbruh@lemmy.one
    link
    fedilink
    arrow-up
    2
    ·
    1 year ago

    I’d say only if you are maxing out the cables respective bandwidth. If it ain’t broke, don’t fix it

  • poVoq@slrpnk.net
    link
    fedilink
    arrow-up
    1
    ·
    1 year ago

    No, cat5e will easily carry 1gbit links and will probably even be fine for anything up to 10gbit.

    If you have a lot of cables going in parallel you might want to check if they are shielded though.

    • boo@beehaw.orgOP
      link
      fedilink
      arrow-up
      0
      ·
      1 year ago

      I have 3 ethernet cables together with a dozen power, audio, display cables. Would it be better if I have a separate bundle for them? How would i check if they are shielded? They are around a meter long each.

      • poVoq@slrpnk.net
        link
        fedilink
        arrow-up
        0
        ·
        1 year ago

        If it’s only a meter, don’t worry about it.

        You can guess if it is shielded or not by how hard the cables are to bend, but otherwise you need to cut them open and see if there is some metalized foil wrapped around the cables. I think this shielding is not mandatory by the specs so usually only the professional ones have it.

        • Étienne@lemmy.efesser.me
          link
          fedilink
          arrow-up
          1
          ·
          1 year ago

          It could be labeled on the cable as well. Look for “UTP” (unshielded), “FTP” or “STP” (two different shielding types).